Netgear Orbi is a solution for most consumers who desire a strong and consistent wifi signal in every residence room. We can confidently claim that everyone is pleased with how well it performs its function. Nevertheless, the Orbi WiFi mesh system is susceptible to specific issues like any other device. Given that internet connection issues may be quite distressing in the modern era, it is necessary to know what to do in such cases.
The problem we will discuss in this article is the orbi flashing white light. Continue reading to learn what it implies, what is causing it, and how to repair it.
Orbi White Flashing Light:
In contrast, a pulsating white light on one of your satellites indicates that the satellite is booting up or attempting to synchronize with the network.
As can be seen, there is little unusual about this conduct. However, the duration of this orbi satellite flashing white should not be excessive. Therefore, we must take action, and the following are the most common remedies.
How To Repair The Orbi White Flashing Light
The following tested remedies should assist you in resolving the Orbi white light flashing issue.
Reboot the Orbi Network
We propose restarting your Orbi network as the first solution. A software error probably caused the issue; therefore, a quick restart should resolve the issue.
To correctly restart your Orbi network, please pay close attention and execute the steps in the following order.
- Deactivate the modem
- Unplug the modem from its source of power.
- Turn the router off.
- Connect the modem’s power supply
- Turn on the modem. Give it some time to boot up fully.
- Turn on the router and wait for two to three minutes to fully boot up.
After restarting the network, the white blinking light should be resolved. Nonetheless, if it continues to flicker, proceed to the next step.
Re-Sync and Generate a New Backhaul Password
You must log in to your Orbi router and generate a new backhaul password. If you’re wondering what a “backhaul password” is, it’s a password or security key that enables the communication between the main router and satellites.
Creating a new backhaul password is straightforward, but you must first log in to your Orbi router’s settings. However, you must remember that the router and satellites must be resynchronized after you generate them. Here is what must be done:
Authenticate to your Orbi router. If you do not know how to access the settings for your Orbi router, you can follow our guide.
- When the Basic Home Page appears, select ADVANCED from the menu.
- Select Wireless Settings after clicking Advanced Setup.
- In the Backhaul Password section, click on the Generate button.
- A new password for the backhaul is generated.
- Use this new backhaul password to synchronize the router and satellites.
- Orbi backhaul security code
After completing this procedure, the white light on your Orbi router will likely stop blinking. However, if the problem persists, try the following solution.
Upgrade The Firmware As Required
According to several users, the orbi blinking white was resolved following a firmware update. Although most ISPs push firmware updates automatically whenever a new version is released, verifying that your Orbi router has the most recent version installed is still good practice. The most current version of the router’s firmware protects it against the most recent online dangers and, in certain circumstances, delivers speed enhancements, which is another incentive to check it frequently.
If you opt to upgrade the router’s firmware, we must warn you that the procedure cannot be halted, or the router may be destroyed.
- Follow these procedures to simply upgrade the router’s firmware via the Orbi admin panel.
- Log in to the admin panel for the Orbi router.
- Now select Advanced from the menu.
- Choose the Administration on orbilogin.com.
- Click Firmware update and then Online update on this page.
- When you click the Check button, the router will determine if fresh firmware is available.
- If an update is available, you can click Update All.
- Give the firmware upgrade some time to complete, and during that time, do not touch anything — do not switch off the router or your device, do not open other tabs to continue browsing, and do not quit the browser. Wait till the firmware update is complete.
- In conclusion, the Orbi router and satellites should restart, and when they boot up again, the new firmware version will be deployed.
Restore Your Orbi Router’s Default Settings
Occasionally, nothing you do yields results. In this situation, we must reset the router to its factory settings. Hopefully, this will resolve the issue, and the blinking white light will cease. However, there is one thing you should be aware of: once the factory reset is complete, you will need to reconfigure the network because any custom settings will be deleted. If you are okay with it, you may proceed.
Last Words
Hopefully, one of the options offered in this post was able to assist you in resolving the Orbi white light blinking issue. However, if you have tried everything and the orbi satellite flashing white persists, feel free to contact your Internet service provider for assistance. They can examine your line and conduct remote diagnostics to determine the source of the issue. It is quite likely that they will either fix it for you or walk you through the necessary steps. Eventually, if remote support fails to resolve the issue, a technician will be dispatched to investigate. Possibly, you are dealing with a faulty router, or they could not detect the cause remotely. This will help you resolve the issue without a doubt.
