Your installation’s success depends on selecting the right plenum cable. The cables in the average home are about 200 feet long. This suggests that after a few runs, these figures will start to add up, so you should make sure your installation is perfect.
This problem can be resolved by buying cable in bulk lengths, which gives you the freedom to run cable anywhere you choose. If you are reading this, it is likely that you need to install cable in an open area of your home or place of business. Whether you’re installing it yourself or hiring a specialist, knowing which Cat6 plenum cable is ideal for your needs is essential.
There are some basics things that you need to look for before buying an Ethernet cable. They are defined below in this article.
Table of Contents
Understanding of Cat6 Plenum Cable?
An Ethernet cable that performs well in locations with air flow is Cat6 plenum 1000ft cable. The Cat6 section, which has a maximum length of 328 feet and a bandwidth of 550MHz, provides best performance of delivering 10Gbps data speed up to 50 meters. Above 50 meters, its speed drops down to 1Gbps.
Because of their stronger crosstalk and EMI resistance, Cat6 cables perform better than Cat5e cables. In the best-case scenario, adding the most recent IEEE 802.3bz standards, 2.5GBase-T and 5GBase-T, will enable you to attain even better performance.
The segment of the cable that is covered by the jacket is referred to as the plenum. When used in areas with air circulation, plenum cables must be made of the most flame-retardant material possible. Plenum cables usually contain insulation consisting of FEP and low smoke flame retardant PVC jackets in order to perform at higher temperatures.
This material is excellent since it successfully prevents flames from spreading and produces far less toxic smoke. Let’s go on to choosing the cable that will be most effective for your application after thoroughly studying the foundations of cat 6 plenum cables.
Impact of Environment: –
One of the most important steps in the purchasing process is selecting the right cable for the location. When employing Cat6 plenum cables, there are two main kinds of issues that you could encounter. Regions with and without EMI are two examples. This covers the majority of installations if you want to install cable in your home.
· Cat6 Plenum Unshielded Cable: –
It is best to install at the places that are EMI free or where the impact of EMI is very low. At such places you do not need to install expensive shielded Ethernet cables. Cat6 plenum unshielded cable is the best available option for such networks.
It does not matter whether you are installing it in the homes or at small commercial networks. You only need to determine the amount of impact of interference factors on the Ethernet cables where you are going to install them.
· Cat6 Plenum Shielded Cable: –
These cable are mostly utilized in the large commercial networks or in the networks which are located at the locations where interference factors are extremely high. The extra shielding on the conductor cables plays well against these interference factors and enhances the performance of the cable to a great extent.
Types of Cat6 Plenum Cable: –
It is available in the market in different types. The most demanding ones are mentioned below.
- Cat6 Shielded Pure Copper Cable
- Cat6 Unshielded Pure Copper Cable
- Cat6 Unshielded Copper-Clad Cable
With that, some other variants of Category 6 cables are also available in the market such as Cat6 Riser, Cat6 Direct burial, and others. It depends on the user requirements and needs to buy one specific cable out of these variants.
On the other hand, it is not necessary that you buy only one variant of the cable to install in one network. You can use them in a combination as well according to the needs and requirements of the network.
Certifications: –
When choosing Cat6 Solid Copper Plenum cable, the certification of your cable may be the most important consideration. It’s important to consider both the certifications your cables have and how they were constructed.
First and foremost, make sure the cable is made of sturdy, 100 percent pure copper conductors. An option to this that is frequently less expensive is copper-clad aluminum (CCA). It is advisable to install Ethernet wire using only pure copper. Copper-clad aluminum will be of inferior quality and may present a safety risk. Working with plenum cable requires the greatest cable you can get, and ensuring that your cable is composed of pure copper will boost your dependability.
The second part of certification is the lab that evaluates your cables. Two of the most well-known testing facilities are ETL and UL. Due to the fact that UL is the leading testing facility in the sector, your cables will have been put through the most stringent industry testing standards. Being UL certified is the only way to guarantee the highest level of safety conformity, even when every other lab conducts testing in accordance with UL requirements.
