If the refrigerator door seal or gasket is ripped, it should be fixed as soon as possible to maintain good operation and avoid a costly power bill. A ripped refrigerator door seal is frequently to blame for the refrigerator’s inability to chill or the freezer’s inability to freeze. A ripped refrigerator door seal might also result in an increase in your electricity cost since the refrigerator needs to work extra hard to keep everything cool. It can also cause frost to form in the freezer, obstructing airflow between the refrigerator and freezer.
If the door seal is ripped or cracked, it should be replaced rather than repaired in most circumstances. However, if the damage is modest, it may be possible to fix it.
Quick Fix
If a little section of the door seal is not grasping the refrigerator door, silicone grease or petroleum jelly might be used to repair it. Simply dab a cotton swab with silicone grease or petroleum jelly and insert it into the groove beneath the loose rubber. This should make pushing the rubber back into position and sealing any leaks much easier.
Repair the Door Seal
Waxed paper and silicone sealant can be used to repair a damaged door seal.
- Remove grease, filth, and mould from the door seal.
- Apply a thin layer of silicone sealant to the damaged area, making sure it reaches any cracks in the seal.
- Using a 2-inch strip of waxed paper, carefully cover the silicone. At either end, make sure it overlaps the undamaged piece of the seal.
- Trim the waxed paper’s edges so that it may be folded to match the seal’s original shape.
- Close the refrigerator door carefully once the sealant and paper are in place. The paper should be trapped between the seal and the refrigerator body as a result.
- Allow the sealant to cure for at least 8 hours.
Replace the Door Seal
What You’ll Require
- Petroleum jelly or silicone grease can be used to replace the door seal.
- a cloth or paper towels
- Blow dryer
- Screwdriver
Preparation
Because the refrigerator door must remain open, you may want to take products out of the fridge and store them in a cooler.
Lay out the new door seal 24 hours before installation to prepare it for installation.
Purchasing a New Door Seal
Try to match your refrigerator’s make and model number to the replacement door seal. Although a universal door seal may work, it is critical to have a replacement door seal that fits properly.
Taking Out the Old Door Seal
The type of door seal on the refrigerator will determine how to remove the old one. In most circumstances, you’ll be able to get away with it. There are screws surrounding the door liner that need to be unfastened if the door seal is installed between the outer and inner panels. Remove the old seal once it has been loosened.
Prepare the Door Seal
Door seals are commonly folded to fit into their packaging. Before you can fit the door seal to the refrigerator, you’ll need to unfold it and eliminate the twists and kinks.
Leave the door seal to dry for 24 hours on a flat, stable surface. This will aid in the restoration of the door seal’s original shape and form.
Heat the Door Seal
Heat from a blow dryer set on low can be used to remove kinks and folds in the door seal. This will make installing the refrigerator door seal much easier. Blow-dry the door seal while straightening it out and removing creases with your fingertips. It’s also possible to prepare the door seal for installation by soaking it in hot water in a tub or sink.
Clean the Area
Clean and dry the place on the refrigerator where the new door seal will go before installing it. This will aid in the adhesion of the new door seal to the door.
Attach the Door Seal
There are three types of door seals that are often used. The first version is simpler to install because it simply pushes into a groove around the door’s perimeter. Fit the door seal to the refrigerator door by pressing hard on it with your fingertips.
Another type of door seal is held in place by a retainer lip that fits behind the door’s liner. You can adhere it to the lip by pressing firmly with your fingers. This form of door seal takes a bit more effort to fit and connect, but it’s also rather simple to install.
The third type of door seal necessitates loosening screws around the door liner in order to fit the door seal between the outer and inner door panels. Place the replacement door seal at the top of the door after freeing the screws. Begin with the top corners and the door seal, then work your way down to the bottom half.
Check the Door Seal
Close the door after the door seal installation is complete to ensure that the seal seals evenly around the door. Examine each piece of the door seal carefully for areas where the seal may not have been properly attached. If you detect any problems, apply a low heat with a blow dryer and smooth out the parts with your fingertips.
If your fridge seal is repaired but your other appliances have issues like washing machine repair abu dhabi, dishwasher repair, dryer repair, etc. then you must read this article.
