It’s crucial to perform routine ducted heating cleaning to keep everyone in your house healthy and free from obnoxious odours. In some cases, dust and debris can accumulate inside your ventilation system and obstruct airflow causing the furnace evaporator coil and blower to malfunction.
This may make your appliance work harder and consume more energy, increasing the cost of operation. You can also appoint a duct cleaning service Melbourne to get a better service. You must clean the duct heating regularly. Below listed are the processes to clean ducted heating:
Table of Contents
What is duct cleaning?
During an air duct cleaning, the complete HVAC system is inspected for any collected particulates contributing to poor air quality. Although it seems straightforward, the biggest issue frequently arises is that dust will stick to the surface of ducts. Therefore, using a conventional vacuum hose near a vent will effectively remove the dust from the interior surfaces. It must be effectively washed off and collected to prevent dust from being blown into other rooms of the house.
Turn of the power:
You should shut off the electricity to the associated heating and cooling system. Any potential electrocutions or mishaps will be avoided by doing this. You should do regular maintenance to have a duct without repair for an extended period.
Gather the equipment:
You need a dryer vent brush, warm, soapy water, cleaning cloths, and a vacuum with a dust brush to clean the air ducts. A step stool and a screwdriver are also required to access wall or ceiling vents. By appointing a ducted heating service and cleaning Melbourne, they can easily clean your duct with their highly equipped materials.
Cover vent with open towels:
A few paper towels might be used to cover the supply register apertures. As a result, when cleaning ducts in other areas of the HVAC system, dust won’t blow out of them and drop on your walls and floor. When cleaning you need to remove the covers and it is a good idea to put them back on after you are done.
Remove the air duct covers:
Using a screwdriver, remove the air duct covers and grilles from the walls. To remove the dust buildup on the wall registers, thoroughly clean them with a brush. Consider washing the registers in hot, soapy water if brushing is ineffective due to severe dustiness. Follow the same procedure for the floor duct covers. You can reach into your ducts and remove any heavy stuff by hand after removing the vents. If your ducts are on the floor and you have young children or dogs, you can find things like pencils, small toys, or even a dog bone hiding there.
Prepare the drill:
Using a drill and a brush to remove dirt, dust, webs, and perhaps mould is a simple method. Find the register and open it, these can occasionally be found on the wall or the floor. Open the register and then insert your drill brush into the duct. Because you don’t want a loose meeting in the ducts, ensure it is fastened firmly.
Then, whirl the brush around inside the ducts while running the drill. Pull it back gradually while the drill is running. This will also clean the duct walls. Stop the drill when the brush is about two feet from the aperture to avoid dust blowing everywhere.
Vacuum your ducts:
It’s time to clean the ducts after cleaning the covers and grilles. The household vacuum won’t be adequate for the job. Therefore you need to hire a heavy-duty vacuum. So, purchase a powerful cleaner to give the ducts a thorough cleaning. A long hose is necessary for the suction to reach further into the ducts. The mould and mildew that may have developed inside the vents can be removed using a strong vacuum.
Clean the ceiling covers:
You can appoint professionals if it is not possible for you to clean the ceiling ducts on your own. It could be challenging to access the ceiling grills with a vacuum. So, think about using a broom. Use the broom to clear the dust from the covers, but don’t forget to wear your dust mask.
Clean inside your duct:
Insert the vent brush into the duct. Rotate the brush while moving it along the duct’s interior surfaces. Tapping exposed ductwork a few times will assist in releasing the junk if it is located somewhere exposed, such as a basement. Finally, remove the brush and extend your vacuum cleaners hose as far as it will go to clear the debris.
Bottom line:
Reinstall the clean vent cover, and then turn the thermostat on. For 30 minutes, let your system run to filter any concealed dust that was disturbed during cleaning. Change the air filter in your system to get rid of all the excess dust gathered for you after the allotted thirty minutes. A regular maintenance is important to have a proper ducted heating for a long period.
